[NEW-642-035-Dumps]Braindump2go 642-035 Exam Dump PDF VCE 175Q&As Free Offer[11-20]

Dec 22, 2016

2016/12 New Cisco 642-035: Troubleshooting Cisco Unified Computing (DCUCT) Exam Questions Updated Today!
Free Instant Download 642-035 Exam Dumps (PDF & VCE) 175Q&As from Braindump2go.com Today!

100% Real Exam Questions! 100% Exam Pass Guaranteed!

1.|2016/12 New 642-035 Exam Dumps (PDF & VCE) 175Q&As Download:
http://www.braindump2go.com/642-035.html

2.|2016/12 New 642-035 Exam Questions & Answers:
https://1drv.ms/f/s!AvI7wzKf6QBjgTXBG4XYyqC6-T8u

QUESTION 11
Looking at the Equipment > Chassis > Servers > Server X view from the Cisco UCS Manager GUI, which tab would you select to identify the fabric interconnect uplink associated with a given virtual circuit?

A.    Paths
B.    vNIC Paths
C.    Virtual Circuit Paths
D.    VIF Paths

Answer: D

QUESTION 12
While attempting to boot a Cisco UCS server from SAN, you are unable to see the LUN. Which of these are causing the problem? (Choose three.)

A.    VHBA template
B.    RAID policy
C.    zoning
D.    LUN ID
E.    vACLs
F.    disjoint fabrics

Answer: ACD

QUESTION 13
A Cisco UCS chassis has two ports on I/O Module 1 connected to Fabric Interconnect A, and two ports on I/O Module 2 connected to Fabric Interconnect B. The I/O modules are connected to ports 1 and 2 on their respective fabric interconnects, and end host mode is configured. After a link failure occurs on port 1 of I/O Module 1, what happens to the traffic that was pinned to that link?

A.    The traffic fails until the link issue is resolved.
B.    The traffic is repinned to I/O Module 2 link 1, which is connected to Fabric Interconnect B.
C.    The traffic is repinned to the remaining link between I/O Module 1 and Fabric Interconnect A.
D.    The traffic is repinned automatically to Fabric Interconnect B.

Answer: C

QUESTION 14
During a password recovery of a Cisco UCS system in a cluster configuration, what happens to blade traffic?

A.    There is no interruption to traffic, as the fabrics go down one at a time.
B.    Traffic stops flowing until the process is complete.
C.    There is no interruption to traffic because both fabrics stay up the whole time.
D.    Traffic will continue to flow, but at a limited rate until the process is complete.

Answer: B

QUESTION 15
For a KVM session to be successful, which two of these need to be done? (Choose two.)

A.    The Cisco IMC IP address needs to be assigned on the Admin tab.
B.    The Cisco IMC IP address needs to be in the same subnet as the management IP.
C.    The Cisco IMC needs to be upgraded to the same version as the UCS Manager.
D.    The server needs to be fully discovered.

Answer: AD

QUESTION 16
As a Cisco UCS administrator, you have a large deployment of C-Series servers. You decide to integrate these into a Cisco UCS Manager environment to simplify management. Which two of these will you need to purchase? (Choose two.)

A.    two fabric interconnects
B.    a dedicated Cisco IMC
C.    two fabric extenders
D.    two I/O modules

Answer: AC

QUESTION 17
Which three Cisco UCS server components can be upgraded via a host firmware package? (Choose three.)

A.    BIOS
B.    Cisco UCS Manager
C.    I/O module
D.    Cisco IMC
E.    fabric interconnect
F.    adapter
G.    board controller

Answer: AFG

QUESTION 18
Which three methods can be used to upgrade the Cisco IMC? (Choose three.)

A.    host firmware package
B.    blade firmware package
C.    controller firmware package
D.    management firmware package
E.    directly on the blade, under the Installed Firmware tab
F.    directly on the blade, under the Blade Firmware tab
G.    directly on the blade, under Inventory > CIMC

Answer: DEG

QUESTION 19
Which of these is a supported Cisco C-Series integration topology?
A)

B)

C)

D)

A.    Exhibit A
B.    Exhibit B
C.    Exhibit C
D.    Exhibit D

Answer: B

QUESTION 20
Which command sequence in the Cisco UCS C-Series rack server CLI sends tech support data to a TFTP server?

A.    ucs-c250 / # scope cimc
ucs-c250 /cimc # scope tech-support
ucs-c250 /cimc/tech-support # set path default.tar.gz
ucs-c250 /cimc/tech-support *# set tftp-ip 192.168.70.45
ucs-c250 /cimc/tech-support *# commit
B.    ucs-c250 / # scope system
ucs-c250 /system # scope tech-support
ucs-c250 /system/tech-support # set path default.tar.gz
ucs-c250 /system/tech-support *# set tftp-ip 192.168.70.45
ucs-c250 /system/tech-support *# commit
C.    ucs-c250 / # scope support
ucs-c250 /support # scope tech-support
ucs-c250 /support/tech-support # set path default.tar.gz
ucs-c250 /support/tech-support *# set tftp-ip 192.168.70.45
ucs-c250 /support/tech-support *# commit
D.    ucs-c250 / # scope fault
ucs-c250 /fault # scope tech-support
ucs-c250 /fault/tech-support # set path default.tar.gz
ucs-c250 /fault/tech-support *# set tftp-ip 192.168.70.45
ucs-c250 /fault/tech-support *# commit