This page was exported from New Braindump2go Exam Dumps [ https://www.eccouncildumps.com ] Export date:Thu Mar 28 9:49:49 2024 / +0000 GMT ___________________________________________________ Title: [February-2023]High Quality Braindump2go 300-410 VCE and 300-410 PDF Dumps 300-410 907Q Free Share[Q354-Q400] --------------------------------------------------- February/2023 Latest Braindump2go 300-410 Exam Dumps with PDF and VCE Free Updated Today! Following are some new Braindump2go 300-410 Real Exam Questions!QUESTION 354What is the function of BFD?A. It provides uniform failure detection regardless of media type.B. It creates high CPU utilization on hardware deployments.C. It negotiates to the highest version if the neighbor version differs.D. It provides uniform failure detection on the same media type.Answer: AQUESTION 355Refer to the exhibit. A network engineer must establish communication between three different customer sites with these requirements: * Site-A: must be restricted to access to any users at Site-B or Site-C.* Site-B and Site-C: must be able to communicate between sites and share routes using OSPF.PE interface configuration:interface FastEthernet0/0ip vrf forwarding Site-A!interface FastEthernet0/1ip vrf forwarding SharedSites!interface FastEthernet0/2ip vrf forwarding SharedSitesWhich configuration meets the requirements?A. PE(config)#router ospf 10 vrf Site-A PE(config-router)#network 0.0.0.0 255.255.255.255 area 0 PE(config)#router ospf 10 vrf SharedSites PE(config-router)#network 0.0.0.0 255.255.255.255 area 1B. PE(config)#router ospf 10 vrf Site-A PE(config-router)#network 0.0.0.0 255.255.255.255 area 0 PE(config)#router ospf 20 vrf SharedSites PE(config-router)#network 0.0.0.0 255.255.255.255 area 1C. PE(config)#router ospf 10 vrf Site-A PE(config-router)#network 0.0.0.0 255.255.255.255 area 0 PE(config)#router ospf 10 vrf SharedSites PE(config-router)#network 0.0.0.0 255.255.255.255 area 0D. PE(config)#router ospf 10 vrf Site-A PE(config-router)#network 0.0.0.0 255.255.255.255 area 0 PE(config)#router ospf 20 vrf SharedSites PE(config-router)#network 0.0.0.0 255.255.255.255 area 0Answer: CQUESTION 356Refer to the exhibit. Site1 must perform unequal cost load balancing toward the segments behind Site2 and Site3. Some of the routes are getting load balanced but others are not. Which configuration allows Site1 to load balance toward all the LAN segments of the remote routers? A. Site3 router eigrp 100 variance 2B. Site2 router eigrp 100 variance 2C. Site2 router eigrp 100 variance 3D. Site1 router eigrp 100 variance 3Answer: DQUESTION 357Refer to the exhibit. An engineer implemented an access list on R1 to allow anyone to Telnet except R2 Loopback0 to R1 Loopback4.How must sequence 20 be replaced on the R1 access list to resolve the issue? A. sequence 20 permit tcp host 1001:ABC:2011:7::1 host 400A:0:400C::1 eq telnetB. sequence 20 deny tcp host 400A:0:400C::1 host 1001:ABC:2011:7::1 eq telnetC. sequence 20 permit tcp host 400A:0:400C::1 host 1001:ABC:2011:7::1 eq telnetD. sequence 20 deny tcp host 1001:ABC:2011:7::1 host 400A:0:400C::1 eq telnetAnswer: DQUESTION 358An engineer notices that R1 does not hold enough log messages to Identity the root cause during troubleshooting.Which command resolves this issue?A. #logging buffered 4096 criticalB. (config)#logging buffered 16000 informationalC. #logging buffered 16000 criticalD. (config)#logging buffered 4096 informationalAnswer: BQUESTION 359Refer to the Exhibit. R1 and R2 use IGP protocol to route traffic between AS 100 and AS 200 despite being configured to use BGP. Which action resolves the issue and ensures the use of BGP? A. Configure distance to 100 under the EIGRP process of R1 and R2.B. Remove distance commands under BGP AS 100 and AS 200.C. Remove distance commands under BGP AS 100.D. Configure distance to 100 under the OSPF process of R1 and R2Answer: BQUESTION 360Refer to the exhibit. An engineer is trying to connect to R1 via Telnet with no success.Which configuration resolves the issue? A. tacacs server prod address ipv4 10.221.10.10 exitB. ip route 10.221.10.10 255.255.255.255 ethernet 0/1C. tacacs server prod address ipv4 10.221.10.11 exitD. ip route 10.221.0.11 255.255.255.255 ethernet 0/1Answer: BQUESTION 361Refer to the exhibit. An engineer must configure PBR on R1 to reach to 10.2.2.0/24 via R3 AS64513 as the primary path and a backup route through default route via R2 AS64513. All BGP routes are in the routing table of R1, but a static default route overrides BGP routes. Which PBR configuration achieves the objective? A. access-list 100 permit ip 10.1.1.0 0.0.0.255 10.2.2.0 0.0.0.255 ! route-map PBR permit 10 match ip address 100 set ip next-hop 10.3.3.1B. access-list 100 permit ip 10.1.1.0 0.0.0.255 10.2.2.0 0.0.0.255 ! route-map PBR permit 10 match ip address 100 set ip next-hop recursive 10.3.3.1C. access-list 100 permit ip 10.1.1.0 255.255.255.0 10.2.2.0 255.255.255.0 ! route-map PBR permit 10 match ip address 100 set ip next-hop recursive 10.3.3.1D. access-list 100 permit ip 10.1.1.0 255.255.255.0 10.2.2.0 255.255.255.0 ! route-map PBR permit 10 match ip address 100 set ip next-hop 10.3.3.1Answer: BQUESTION 362Refer to the exhibit. An administrator configured a Cisco router for TACACS authentication, but the router is using the local enable password instead. Which action resolves the issue? A. Configure the aaa authentication login default group admin local if-authenticated command instead.B. Configure the aaa authentication login admin group tacacs+ local enable none command instead.C. Configure the aaa authentication login admin group tacacs+ local if-authenticated command instead.D. Configure the aaa authentication login admin group admin local enable command instead.Answer: DQUESTION 363How do devices operate in MPLS L3VPN topology?A. P and associated PE routers with IGP populate the VRF table in different VPNs.B. CE routers connect to the provider network and perform LSP functionalityC. P routers provide connectivity between PE devices with MPLS switching.D. P routers support PE to PE VPN tunnel without LSP functionalityAnswer: CQUESTION 364What is LDP label binding?A. neighboring router with labelB. source prefix with labelC. destination prefix with labelD. two routers with label distribution sessionAnswer: CQUESTION 365Which table is used to map the packets in an MPLS LSP that exit from the same interface, via the same next hop, and have the same queuing policies?A. RIBB. FECC. LDPD. CEFAnswer: BExplanation:A forwarding equivalence class (FEC) is a term used in Multiprotocol Label Switching (MPLS) to describe a set of packets with similar or identical characteristics which may be forwarded the same way; that is, they may be bound to the same MPLS label.QUESTION 366Refer to the exhibit. The IT router has been configured with the Science VRF and the interfaces have been assigned to the VRF.Which set of configurations advertises Science-1 and Science-2 routes using EIGRPAS 111? A. router eigrp 111 address-family ipv4 vrf Science autonomous-system 1 network 192.168.1.0 network 192.168.2.0B. router eigrp 111address-family ipv4 vrf Science network 192.168.1.0 network 192.168.2.0C. router eigrp 111 network 192.168.1.0 network 192.168.2.0D. router eigrp 1 address-family ipv4 vrf Science autonomous-system 111 network 192.168.1.0 network 192.168.2.0Answer: DQUESTION 367Refer to the exhibit. When an FTP client attempts to use passive FTP to connect to the FTP server, the file transfers fail Which action resolves the issue? A. Configure active FTP traffic.B. Modify FTP-SERVER access list to remove established at the end.C. Modify traffic filter FTP-SERVER in to the outbound direction.D. Configure to permit TCP ports higher than 1023.Answer: DQUESTION 368In a DMVPN network, the Spoke1 user observed that the voice traffic is coming to Spoke2 users via the hub router. Which command is required on both spoke routers to communicate directly to one another?A. ip nhrp map dynamicB. ip nhrp shortcutC. ip nhrp nhs multicastD. ip nhrp redirectAnswer: BQUESTION 369Refer to the exhibit. The network administrator configured the network to establish connectivity between all devices and notices that the ASBRs do not have routes for each other. Which set of configurations resolves this issue? RR Configuration:router bgp 100neighbor IBGP peer-groupneighbor IBGP route-reflector-clientneighbor 10.1.1.1 remote-as 100neighbor 10.1.2.2 remote-as 100neighbor 10.1.3.3 remote-as 100A. router bgp 100 neighbor IBGP update-source Loopback0B. router bgp 100 neighbor IBGP next-hop-selfC. router bgp 100 neighbor 10.1.1.1 next-hop-self neighbor 10.1.2.2 next-hop-self neighbor 10.1.3.3 next-hop-selfD. router bgp 100 neighbor 10.1.1.1 peer-group IBGP neighbor 10.1.2.2 peer-group IBGP neighbor 10.1.3.3 peer-group IBGPAnswer: DQUESTION 370Refer to the exhibit. The network administrator configured the Chicago router to mutually redistribute the LA and NewYork routes with OSPF routes to be summarized as a single route in EIGRP using the longest summary mask: router eigrp 100 redistribute ospf 1 metric 10 10 10 10 10 router ospf 1 redistribute eigrp 100 subnets!interface E 0/0ip summary-address eigrp 100 172.16.0.0 255.255.0.0After the configuration, the New York router receives all the specific LA routes but the summary route. Which set of configurations resolves the issue on the Chicago router?A. interface E 0/1 ip summary-address eigrp 100 172.16.0.0 255.255.0.0B. interface E 0/1 ip summary-address eigrp 100 172.16.8.0 255.255.252.0C. router eigrp 100 summary-address 172.16.8.0 255.255.252.0D. router eigrp 100 summary-address 172.16.0.0 255.255.0.0Answer: BQUESTION 371Refer to the exhibit. An engineer must configure DMVPN Phase 3 hub-and-spoke topology to enable a spoke-to-spoke tunnel. Which NHRP configuration meets the requirement on R6? A. interface Tunnel 1 ip address 192.168.1.1 255.255.255.0 tunnel source e 0/0 tunnel mode gre multipointip nhrp network-id 1B. interface Tunnel1 ip nhrp authentication Cisco123ip nhrp map multicast dynamicip nhrp network-id 1 ip nhrp holdtime 300 ip nhrp redirectC. interface Tunnel1 ip nhrp authentication Cisco123 ip nhrp map multicast dynamic ip nhrp network-id 1 ip nhrp holdtime 300 ip nhrp shortcutD. interface Tunnel 1 ip address 192.168.1.1 255.255.255.0 tunnel source e 0/1 tunnel mode gre multipoint ip nhrp network-id 1ip nhrp map 192.168.1.2 192.1.20.2Answer: BQUESTION 372Refer to the exhibit. An engineer implemented CoPP to limit Telnet traffic to protect the router CPU. It was noticed that the Telnet traffic did not pass through CoPP.Which configuration resolves the issue? A. policy-map COPP class TELNET police 8000 conform-action transmit exceed-action transmitB. policy-map COPP class TELNET police 8000 conform-action transmit exceed-action transmit violate-action dropC. ip access-list extended TELNET permit tcp host 10.2.2.1 host 10.2.2.4 eq telnet permit tcp host 10.1.1.1 host 10.1.1.3 eq telnetD. ip access-list extended TELNET permit tcp host 10.2.2.4 host 10.2.2.1 eq telnet permit tcp host 10.1.1.3 host 10.1.1.1 eq telnetAnswer: DQUESTION 373Refer to the exhibit. An engineer implemented CoPP but did not see OSPF traffic going through it. Which configuration resolves the issue? A. ip access-list extended OSFP permit ospf any anyB. policy-map COPP class OSFP police 8000 conform-action transmit exceed-action transmit violate-action dropC. control-plane service-policy input COPPD. class-map match-all OSFP match access-group name OSFPAnswer: AQUESTION 374An engineer must override the normal routing behavior of a router for Telnet traffic that is destined to 10.10.10.10 from 10.10.1.0/24 via a next hop of 10.4.4.4 which is directly connected to the router that is connected to the 10.1.1.0/24 subnet.Which configuration reroutes traffic according to this requirement? A. Option AB. Option BC. Option CD. Option DAnswer: BQUESTION 375Refer to the exhibit. An engineer must redistribute networks 192.168.10.0/24 and 192.168.20.0/24 into OSPF from EIGRP. Where the metric must be added when traversing through multiple hops to start an external route of 20. The engineer notices that the external metric is fixed and does not add at each hop. Which configuration resolves the issue? A. R2(config)#access-list 10 permit 192.168.10.0 0.0.0.255 R2(config)#access-list 10 permit 192.168.20.0 0.0.0.255 ! R2(config)#route-map RD permit 10 R2(config-route-map)#match ip address 10 R2(config-route-map)#set metric 20 R2(config-route-map)#set metric-type type-2 ! R2(config)#router ospf 10 R2(confjg-router)#redistribute eigrp 10 subnets route-map RDB. R2(config)#access-list 10 permit 192.168.10.0 0.0.0.255 R2(config)#access-list 10 permit 192.168.20.0 0.0.0.255 ! R2(config)#route-map RD permit 10 R2(config-route-map)#match ip address 10 R2(config-route-map)#set metric 20 R2(config-route-map)#set metric-type type-1 ! R2(config)#router ospf 10 R2(config-router)#redistribute eigrp 10 subnets route-map RDC. R1(config)#access-list 10 permit 192.168.10.0 0.0.0.255 (config)#access-list 10 permit 192.168.20.0 0.0.0.255 ! R1(config)#route-map RD permit 10 R1(config-route-map)#match ip address 10 R1(config-route-map)#set metric 20 R1(config-route-map)#set metric-type type-1 ! R1(config)#router ospf 10 R1(config-router)#redistribute eigrp 10 subnets route-map RDD. R1(config)#access-list 10 permit 192.168.10.0 0.0.0.255 R1(config)#access-list 10 permit 192.168.20.0 0.0.0.255 ! R1(config)#route-map RD permit 10 R1(config-route-map)#match ip address 10 R1(config-route-map)#set metric 20 R1(config-route-map)#set metric-type type-2 ! R1(config)#router ospf 10 R1(config-router)#redistribute eigrp 10 subnets route-map RDAnswer: BQUESTION 376An administrator attempts to download the pack NBAR2 file using TFTP from the CPE router to another device over the Gi0/0 interface. The CPE is configured as below:hostname CPE!ip access-list extended WAN< `¦>remark => All UDP rules below for WAN ID: S421T18E58F90permit udp any eq domain anypermit udp any any eq tftpdeny udp any any!interface GigabitEthernet0/0< `¦>ip access-group WAN in< `¦>!tftp-server flash:pp-adv-csr1000v-1612.1a-37-53.0.0.packThe transfer fails. Which action resolves the issue?A. Change the WAN ACL to permit the UDP port 69 to allow TFTPB. Make the permit udp any eq tftp any entry the last entry in the WAN ACL.C. Change the WAN ACL to permit the entire UDP destination port rangeD. Shorten the file name to the 8+3 naming convention.Answer: BQUESTION 377What is an MPLS LDP targeted session?A. session between neighbors that are connected no more than one hop awayB. LDP session established between LSRs by exchanging TCP hello packetsC. label distribution session between non-directly connected neighborsD. LDP session established by exchanging multicast hello packetsAnswer: CQUESTION 378Refer to the exhibit. An administrator configures a router to stop using a particular default route if the DNS server 8.8.8.8 is not reachable through that route. However, this configuration did not work as desired and the default route still works even if the DNS server 8.8.8 8 is unreachable. Which two configuration changes resolve the issue? (Choose two.) A. Configure two static routes for the 8.8.8.8/32 destination to match the IP SLA probe for each ISP.B. Associate every IP SLA probe with the proper WAN address of the router.C. Reference the proper exit interfaces along with the next hops in both static default routes.D. Use a separate track object to reference the existing IP SLA 1 probe for every static route.E. Use a separate IP SLA probe and track object for every static routeAnswer: AEQUESTION 379Refer to the exhibit. A network administrator must block ping from user 3 to the App Server only. An inbound standard access list is applied to R1 interface G0/0 to block ping. The network administrator was notified that user 3 cannot even ping user 9 anymore.Where must the access list be applied in the outgoing direction to resolve the issue? A. R2 interface G1/0B. R2 interface G0/0C. SW1 interface G1/10D. SW1 interface G2/21Answer: DQUESTION 380Refer to the exhibit. Refer to the exhibit. A network engineer receives a report that Spoke 1 users can perform bank transactions with the server located at the Center site, but Spoke 2 users cannot. Which action resolves the issue? A. Configure the Spoke 2 users IP on the router B OSPF domainB. Configure encapsulation dot1q 78 on the router C interface.C. Configure IPv6 on the routers B and C interfacesD. Configure OSPFv2 on the routers B and C interfacesAnswer: CQUESTION 381Refer to the exhibit. An engineer configured route exchange between two different companies for a migration project. EIGRP routes were learned in router C, but no OSPF routes were learned in router A. Which configuration allows router A to receive OSPF routes? A. (config-router-af-topology)#no redistribute ospf 10 match external 1 external 2 metric 1000000 10 255 1 1500B. (config-router-af)#redistribute ospf 10 1000000 10 255 1 1500C. (config-router-af-topology)#redistribute connectedD. (config-router-af-topology)#redistribute ospf 10 metric 1000000 10 255 1 1500Answer: DQUESTION 382A network administrator cannot connect to a device via SSH. The line vty configuration is as follows: Which action resolves this issue?A. Increase the session timeoutB. Change the stopbits to 10.C. Configure the transport input SSHD. initialize the SSH keyAnswer: DQUESTION 383Refer to the exhibits. London must reach Rome using a faster path via EIGRP if all the links are up but it failed to take this path. Which action resolves the issue? A. Increase the bandwidth of the link between London and Barcelona.B. Use the network statement on London to inject the 172.16.X.0/24 networks into EIGRP.C. Change the administrative distance of RIP to 150.D. Use the network statement on Rome to inject the 172.16.X.0/24 networks into EIGRP.Answer: DQUESTION 384Refer to the exhibit. The company implemented uRPF to address an antispoofing attack. A network engineer received a call from the IT security department that the regional data center is under an IP attack. Which configuration must be implemented on R1 to resolve this issue? A. Option AB. Option BC. Option CD. Option DAnswer: BQUESTION 385What is a function of BFD?A. peer recovery after a Layer 3 protocol adjacency failureB. peer recovery after a Layer 2 adjacency failureC. failure detection independent of routing protocols and media typesD. failure detection dependent on routing protocols and media typesAnswer: DQUESTION 386Refer to the exhibit. AS 111 mut not be used as a transit AS, but ISP-1 is getting ISP-2 routes from AS 111. Which configuration stops Customer AS from being used as a transit path on ISP-1? A. ip as-path access-list 1 permit ^$B. ip as-path access-list 1 permit_111_C. ip as-path access-list 1 permit."D. ip as-path access-list 1 permit ^111$Answer: AQUESTION 387Refer to the exhibit. An engineer configured user login based on authentication database on the router, but no one can log into the router.Which configuration resolves the issue? A. aaa authentication login default enableB. aaa authorization network default localC. aaa authentication login default localD. aaa authorization exec default localAnswer: CQUESTION 388Refer to the exhibit. An engineer configured NetFlow on R1, but the flows do not reach the NMS server from R1. Which configuration resolves this Issue? A. R1(config)#flow monitor FlowMonitort1R1(config-flow-monitor)#destination 10.66.66.66B. R1(config)#interface Ethernet0/0R1(config-if)#ip flow monitor Flowmonitor1 inputR1(config-if)#ip flow monitor Flowmonitor1 outputC. R1(config)#interface Ethernet0/1R1(config-if)#ip flow monitor Flowmonitor1 inputR1(config-if)#ip flow monitor Flowmonitor1 outputD. R1(config)#flow exporter FlowExporter1R1(config-flow-exporter)#destination 10.66.66.66Answer: DQUESTION 389Refer to the exhibit. The engineer configured route redistribution in the network but soon received reports that R2 cannot access 192.168.7.0/24 and 192.168.15.0/24 subnets.Which configuration resolves the issue? A. Option AB. Option BC. Option CD. Option DAnswer: DQUESTION 390An engineer received a ticket about a router that has reloaded. The monitoring system graphs show different traffic patterns between logical and physical interfaces when the router is rebooted. Which action resolves the issue?A. Configure the snmp ifindex persist command globally.B. Clear the logical interfaces with snmp ifindex clear commandC. Configure the snmp ifindex persist command on the physical interfaces.D. Trigger a new snmpwalk from the monitoring system to synchronize interface OlDsAnswer: AQUESTION 391Which of the following is true regarding IPsec Pre-fragmentation (Look-Ahead Fragmentation)? (Choose two.)A. Operates in tunnel mode onlyB. Operates in transport mode onlyC. Is used to help in the overall IPsec throughput since the end host is able to avoid packet reassembly after packet decryption.D. Is not dependent on the MTU of the physical interface used for IPsec.E. Does not support Path MTU DiscoveryAnswer: ACQUESTION 392Refer to the exhibit. Which action limits the access to R2 from 192.168.12.1? A. Swap sequence 10 with sequence 20 in access-list 100.B. Modify sequence 20 to permit tcp host 192.168.12.1 eq 22 any to access-list 100C. Swap sequence 20 with sequence 10 in access-list 100D. Modify sequence 10 to deny tcp any eq 22 any to access-list 100.Answer: CQUESTION 393Refer to the exhibit. The route to 192.168.200.0 is flapping between R1 and R2. Which set of configuration changes resolves the flapping route? A. R2(config)#router ospf 100R2(config-router)#no redistribute eigrp 100R2(config-router)#redistribute eigrp 100 metric 1 subnetsB. R1(config)#no router ripR1(config)#ip route 192.168.200.0 255.255.255.0 10.40.0.2C. R2(config)#router eigrp 100R2(config-router)#no redistribute ospf 100R2(config-router)#redistribute ripD. R1(config)#router ospf 100R1(config-router)#redistribute rip metric 1 metric-type 1 subnetsAnswer: DQUESTION 394Which feature is used by LDP in the forwarding path within the MPLS cloud?A. IP forwardingB. TTLC. TDPD. LSPAnswer: DQUESTION 395Refer to the exhibit. After recovering from a power failure. Ethernet0/1 stayed down while Ethernet0/0 returned to the up/up state. The default route through ISP1 was not reinstated m the routing table until Ethernet0/1 also came up. Which action resolves the issue? A. Reference the track object 1 in both static default routesB. Remove the references to the interface names from both static default routesC. Configure the default route through ISP1 with a higher administrative distance than 2.D. Add a static route to the 8.8.8.8/32 destination through the next hop 203.0.113.1Answer: AQUESTION 396Refer to me exhibit. The hub and spoke are connected via two DMVPN tunnel interfaces.The NHRP is configured and the tunnels are detected on the hub and the spoke.Which configuration command adds an IPsec profile on both tunnel interfaces to encrypt traffic? A. tunnel protection ipsec profile DMVPN multipointB. tunnel protection ipsec profile DMVPN tunnel1C. tunnel protection ipsec profile DMVPN sharedD. tunnel protection ipsec profile DMVPN uniqueAnswer: CQUESTION 397Refer to the exhibit. The administrator is troubleshooting a BGP peering between PE1 and PE3 that is unable to establish.Which action resolves the issue? A. P2 must have a route to PE3 to establish a BGP session to PE1B. Disable sending ICMP unreachables on P2 to allow PE1 to establish a session with PE3C. Ensure that the PE3 loopback address is used as a source for BGP peering to PE1D. Remove the traffic filtering rules on P2 blocking the BGP communication between PE1 and PE3Answer: CQUESTION 398Refer to the exhibit. An engineer configured SNMP community on UserSW2 switch, but the SNMP server cannot upload modified configurations to the switch.Which configuration resolves this issue? A. snmp-server community Ciscowruser RW 11B. snmp-server group NETADMIN v3 priv read NETVIEW write NETADMIN access 22C. snmp-server community CiscOUs3r RW 11D. snmp-server group NETVIEW v2c priv read NETVIEW access 11Answer: AQUESTION 399Refer to the exhibit. The remote branch locations have a static neighbor relationship configured to R1 only R1 has successful neighbor relationships with the remote locations of R2 and R3, but the end users cannot communicate with each other. Which configuration resolves the issue? A. Option AB. Option BC. Option CD. Option DE. Option EAnswer: EQUESTION 400Refer to the exhibit. The authentication is not working as desired and the user drops into user-exec mode. Which configuration resolves the issue? A. Option AB. Option BC. Option CD. Option DAnswer: CResources From:1.2023 Latest Braindump2go 300-410 Exam Dumps (PDF & VCE) Free Share:https://www.braindump2go.com/300-410.html2.2023 Latest Braindump2go 300-410 PDF and 300-410 VCE Dumps Free Share:https://drive.google.com/drive/folders/1NkZ6PH5JebhsyHrMEXD3IWxkOLRjQ-B-?usp=sharingFree Resources from Braindump2go,We Devoted to Helping You 100% Pass All Exams! --------------------------------------------------- Images: --------------------------------------------------- --------------------------------------------------- Post date: 2023-02-23 07:00:30 Post date GMT: 2023-02-23 07:00:30 Post modified date: 2023-02-23 07:00:30 Post modified date GMT: 2023-02-23 07:00:30 ____________________________________________________________________________________________ Export of Post and Page as text file has been powered by [ Universal Post Manager ] plugin from www.gconverters.com