[Dec.-2016-New]Braindump2go 300-115 (PDF & VCE)Dumps 230Q&As Free Offer[101-110]

2016 Dec. New Cisco 300-115: Implementing Cisco IP Switched Networks (SWITCH v2.0) Exam Questions Updated Today!
Free Instant Download 300-115 Exam Dumps (PDF & VCE) 230q download from Braindump2go.com Today!

100% Real Exam Questions! 100% Exam Pass Guaranteed!

1.|2016 Dec. New 300-115 Exam Dumps (PDF & VCE) 230q download:
http://www.braindump2go.com/300-115.html
2.|2016 Dec. New 300-115 Exam Questions & Answers:
https://1drv.ms/f/s!AvI7wzKf6QBjgSVgicaB52AMWrK2

QUESTION 101
Hotspot – HSRP
Ferris Plastics, Inc. is a medium sized company, with an enterprise network (access, distribution and core switches) that provides LAN connectivity from user PCs to corporate servers. The distribution switches are configured to use HSRPto provide a high availability solution.
– DSW1 -primary device for VLAN 101 VLAN 102 andVLAN 105
– DSW2 – primary device for VLAN 103 and VLAN 104
– A failure of GigabitEthemet1/0/1 on primary device should cause the primary device to release its status as the primary device, unless GigabitEthernet1/0/1 on backup device has also failed.
Troubleshooting has identified several issues. Currently all interfaces are up. Using the running configurations and show commands, you have been asked to investigate and respond to the following question.
 
During routine maintenance, it became necessary to shut down the GigabitEthernet1/0/1 interface on DSW1. All other interfaces were up. During this time, DSW1 remained the active device for the VLAN 102 HSRP group. You have determined that there is an issue with the decrement value in the track command for the VLAN 102 HSRP group. What needs to be done to make the group function properly?

A.    The decrement value on DSW1 should be greaterthan 5 and less than 15. 0
B.    The decrement value on DSW1 should be greaterthan 9 and less than 15.
C.    The decrement value on DSW1 should be greaterthan 11 and less than 19.
D.    The decrement value on DSWTs should be greaterthan 190 and less than 200.
E.    The decrement value on DSWTs should be greaterthan 195 and less than 205.

Answer: C
Explanation:
 
Use “show run” command to show. The left Vlan102 is console1 of DS1. Priority value is 200, we should decrement value in the track command from 11 to 18. Because 200 – 11 = 189 < 190 ( priority of Vlan102 on DS2 ).

QUESTION 102
Hotspot – HSRP
Ferris Plastics, Inc. is a medium sized company, with an enterprise network (access, distribution and core switches) that provides LAN connectivity from user PCs to corporate servers. The distribution switches are configured to use HSRPto provide a high availability solution.
– DSW1 -primary device for VLAN 101 VLAN 102 andVLAN 105
– DSW2 – primary device for VLAN 103 and VLAN 104
– A failure of GigabitEthemet1/0/1 on primary device should cause the primary device to release its status as the primary device, unless GigabitEthernet1/0/1 on backup device has also failed.
Troubleshooting has identified several issues. Currently all interfaces are up. Using the running configurations and show commands, you have been asked to investigate and respond to the following question.
 
All interfaces are active. DSW2 has not become the active device for the VLAN 103 HSRP group. As related to the VLAN 103 HSRP group, what can be done to make the group function properly?

A.    On DSW1, disable preempt.
B.    On DSW1, decrease the priority value to a value less than 190 and greater than 150.
C.    On DSW2, increase the priority value to a value greater 200 and less than 250.
D.    On DSW2, increase the decrement value in the track command to a value greater than 10 and less than 50.

Answer: C
Explanation:
From the output shown below of the HSRP status of DSW2, we see that the active router has a priority of 200, while the local priority is 190. We need to increase the priority of DSW2 to greater than 200, but it should be less than 250 so that if the gig 1/0/1 interface goes down, DSW1 will become active. DSW2 is configured to decrement the priority by 50 if this interface goes down, so the correct answer is to increase the priority to more than 200, but less than 250.
 

QUESTION 103
Hotspot – HSRP
Ferris Plastics, Inc. is a medium sized company, with an enterprise network (access, distribution and core switches) that provides LAN connectivity from user PCs to corporate servers. The distribution switches are configured to use HSRPto provide a high availability solution.
– DSW1 -primary device for VLAN 101 VLAN 102 andVLAN 105
– DSW2 – primary device for VLAN 103 and VLAN 104
– A failure of GigabitEthemet1/0/1 on primary device should cause the primary device to release its status as the primary device, unless GigabitEthernet1/0/1 on backup device has also failed.
Troubleshooting has identified several issues. Currently all interfaces are up. Using the running configurations and show commands, you have been asked to investigate and respond to the following question.
 
During routine maintenance, it became necessary to shut down the GigabitEthernet1/0/1 interface on DSW1 and DSW2. All other interfaces were up. During this time, DSW1 became the active router for the VLAN 104HSRP group. As related to the VLAN 104HSRP group, what can to be done to make the group function properly?

A.    On DSW1, disable preempt.
B.    On DSW2, decrease the priority value to a value less than 150.
C.    On DSW1, increase the decrement value in the track command to a value greater than 6.
D.    On DSW1, decrease the decrement value in the track command to a value less than 1.

Answer: C
Explanation:
 
We should NOT disable preempt on DS1. By do that, you will make Vlan104’s HSRP group fail function.
Example: if we are disable preempt on DS1. It can not become active device when G1/0/1 on DS2 fail. In this question, G0/1/0 on DS1 & DS2 is shutdown. Vlan104 (left) : 150 ­ 1 = 149. Vlan104 (right) : 200 ­ 155 = 145. Result is priority 149 > 145 ( Vlan104 on DS1 is active). If increase the decrement in the track value to a value greater than 6 ( > or = 6). Vlan104 (left) : 150 ­ 6 = 144. Result is priority 144 < 145 ( vlan104 on DS2 is active).

QUESTION 104
Hotspot – HSRP
Ferris Plastics, Inc. is a medium sized company, with an enterprise network (access, distribution and core switches) that provides LAN connectivity from user PCs to corporate servers. The distribution switches are configured to use HSRPto provide a high availability solution.
– DSW1 -primary device for VLAN 101 VLAN 102 andVLAN 105
– DSW2 – primary device for VLAN 103 and VLAN 104
– A failure of GigabitEthemet1/0/1 on primary device should cause the primary device to release its status as the primary device, unless GigabitEthernet1/0/1 on backup device has also failed.
Troubleshooting has identified several issues. Currently all interfaces are up. Using the running configurations and show commands, you have been asked to investigate and respond to the following question.
 
What is the priority value of the VLAN 105 HSRP group on DSW2?

A.    50
B.    100
C.    150
D.    200

Answer: B
Explanation:
Use “show stantby brieft” command on console2. Very easy to see priority of Vlan105 is 100.
 

QUESTION 105
Hotspot – HSRP
Ferris Plastics, Inc. is a medium sized company, with an enterprise network (access, distribution and core switches) that provides LAN connectivity from user PCs to corporate servers. The distribution switches are configured to use HSRPto provide a high availability solution.
– DSW1 -primary device for VLAN 101 VLAN 102 andVLAN 105
– DSW2 – primary device for VLAN 103 and VLAN 104
– A failure of GigabitEthemet1/0/1 on primary device should cause the primary device to release its status as the primary device, unless GigabitEthernet1/0/1 on backup device has also failed.
Troubleshooting has identified several issues. Currently all interfaces are up. Using the running configurations and show commands, you have been asked to investigate and respond to the following question.
 
If GigabitEthemet1/0/1 on DSW2 is shutdown, what will be the resulting priority value of the VLAN 105 HSRP group on router DSW2?

A.    90
B.    100
C.    150
D.    200

Answer: A
Explanation:
As seen below, the current priority for VLAN 105 is 100, and the tracking feature for Gig 1/0/0 is enabled which will decrement the priority by 10 if this interface goes down for a priority value of 90.
 

QUESTION 106
Lab Simulation – MLS and EIGRP
You have been tasked with configuring multilayer SwitchC, which has a partial configuration and has been attached to RouterC as shown in the topology diagram.
You need to configure SwitchC so that Hosts H1 and H2 can successfully ping the server S1. Also SwitchC needs to be able to ping server S1.
Due to administrative restrictions and requirements you should not add/delete vlans or create trunk links. Company policies forbid the use of static or default routing. All routes must be learned via EIGRP 65010 routing protocol.
You do not have access to RouteC. RouterC is correctly configured. No trunking has been configured on RouterC.
Routed interfaces should use the lowest host on a subnet when possible. The following subnets are available to implement this solution:
– 10.10.10.0/24
– 190.200.250.32/27
– 190.200.250.64/27
Hosts H1 and H2 are configured with the correct IP address and default gateway.
SwitchC uses Cisco as the enable password.
Routing must only be enabled for the specific subnets shown in the diagram.
Note: Due to administrative restrictions and requirements you should not add or delete VLANs, changes VLAN port assignments or create trunks. Company policies forbid the use of static or default routing. All routes must be learned via the EIGRP routing protocol.
 
Answer:
In real life, there are two ways to configure interVLAN routing in this case:
+ Use RouterC as a “router on a stick” and SwitchC as a pure Layer2 switch. Trunking must be established between RouterC and SwitchC.
+ Only use SwitchC for interVLAN routing without using RouterC, SwitchC should be configured as a Layer 3 switch (which supports ip routing function as a router). No trunking requires.
The question clearly states “No trunking has been configured on RouterC” so RouterC does not contribute to interVLAN routing of hosts H1 & H2 -> SwitchC must be configured as a Layer 3 switch with SVIs for interVLAN routing.
We should check the default gateways on H1 & H2. Click on H1 and H2 and type the “ipconfig” command to get their default gateways.
C:\>ipconfig
We will get the default gateways as follows:
Host1:
+ Default gateway: 190.200.250.33
Host2:
+ Default gateway: 190.200.250.65
Now we have enough information to configure SwitchC (notice the EIGRP AS in this case is 650)
Note: VLAN2 and VLAN3 were created and gi0/10, gi0/11 interfaces were configured as access ports so we don’t need to configure them in this sim.
SwitchC# configure terminal
SwitchC(config)# int gi0/1
SwitchC(config-if)#no switchport -> without using this command, the simulator does not let you assign IP address on Gi0/1 interface.
SwitchC(config-if)# ip address 10.10.10.2 255.255.255.0 ->RouterC has used IP 10.10.10.1 so this is the lowest usable IP address.
SwitchC(config-if)# no shutdown
SwitchC(config-if)# exit
SwitchC(config)# int vlan 2
SwitchC(config-if)# ip address 190.200.250.33 255.255.255.224
SwitchC(config-if)# no shutdown
SwitchC(config-if)# int vlan 3
SwitchC(config-if)# ip address 190.200.250.65 255.255.255.224
SwitchC(config-if)# no shutdown
SwitchC(config-if)#exit
SwitchC(config)# ip routing (Notice: MLS will not work without this command)
SwitchC(config)# router eigrp 650
SwitchC(config-router)# network 10.10.10.0 0.0.0.255
SwitchC(config-router)# network 190.200.250.32 0.0.0.31
SwitchC(config-router)# network 190.200.250.64 0.0.0.31
NOTE: THE ROUTER IS CORRECTLY CONFIGURED, so you will not miss within it in the exam , also don’t modify/delete any port just do the above configuration. Also some reports said the “no auto-summary” command can’t be used in the simulator, in fact it is not necessary because the network 190.200.0.0/16 is not used anywhere else in this topology.
In order to complete the lab , you should expect the ping to SERVER to succeed from the MLS , and from the PCs as well.
Also make sure you use the correct EIGRP AS number (in the configuration above it is 650 but it will change when you take the exam) but we are not allowed to access RouterC so the only way to find out the EIGRP AS is to look at the exhibit above. If you use wrong AS number, no neighbor relationship is formed between RouterC and SwitchC.
In fact, we are pretty sure instead of using two commands “network 190.200.250.32 0.0.0.31” and “network 190.200.250.64 0.0.0.31” we can use one simple command “network 190.200.0.0” because it is the nature of distance vector routing protocol like EIGRP: only major networks need to be advertised; even without “no auto-summary” command the network still works correctly. But in the exam the sim is just a flash based simulator so we should use two above commands, just for sure. But after finishing the configuration, we can use “show run” command to verify, only the summarized network 190.200.0.0 is shown.

QUESTION 107
Your customer has asked you to come in and verify the operation of routers R1 and R2 which are configured to use HSRP. They have questions about how these two devices will perform in the event of a device failure.
 
What percentage of the outgoing traffic from the 172.16.10.0/24 subnet is being forwarded through R1?

A.    R1-0%
B.    R1-50 %, R2-50%
C.    R2-100%
D.    R1-100%

Answer: D
Explanation:
Based on the following output, we see that R1 is the active standby router for the Ethernet 0/0 link, so all outgoing traffic will be forwarded to R1.
 

QUESTION 108
Your customer has asked you to come in and verify the operation of routers R1 and R2 which are configured to use HSRP. They have questions about how these two devices will perform in the event of a device failure.
 
Refer to the exhibit. If router R1 interface Etherne0/0 goes down and recovers, which of the statement regarding HSRP priority is true?

A.    The interface will have the priority decremented by 40 for HSRP group 1.
B.    The interface will have the priority decremented by 60 for HSRP group 1
C.    The interface will have its current priority incremented by 40 for HSRP group 1
D.    The interface will have its current priority incremented by 60 for HSRP group 1
E.    The interface will default to the a priority of 100 for HSRP group 1

Answer: C
Explanation:
Here is the HSRP configuration seen on R1:
 
Here, when the Ethernet 0/0 interface goes down, the standby 1 track decrement command will lower the priority from 130 to 90. However, when it comes back up, it will then increment it by 40 back to 130 for HSRP group 1.

QUESTION 109
Your customer has asked you to come in and verify the operation of routers R1 and R2 which are configured to use HSRP. They have questions about how these two devices will perform in the event of a device failure.
 
What issue is causing Router R1 and R2 to both be displayed as the HSRP active router for group 2?

A.    The HSRP group number mismatch
B.    The HSRP group authentication is misconfigured
C.    The HSRP Hello packets are blocked
D.    The HSRP timers mismatch
E.    The HSRP group priorities are different

Answer: B
Explanation:
Based on the configuration output, we see that authentication is configured on R2, but not on R1:
 
 
This can be further verified by issuing the “show standby” command on each router.
 
\\psf\Home\.Trash\Screen Shot 2014-10-16 at 4.45.29 PM.png

QUESTION 110
Your customer has asked you to come in and verify the operation of routers R1 and R2 which are configured to use HSRP. They have questions about how these two devices will perform in the event of a device failure.
 
What is the virtual mac-address of HSRP group 1?

A.    0000.0c07.ac02
B.    4000.0000.0010
C.    0000.0c07.ac01
D.    4000.0000.ac01
E.    4000.0000.ac02
F.    0000.0c07.0010

Answer: B
Explanation:
Issuing the “show standby” command on either router shows us that the virtual MAC used by HSRP group 1 is 4000.0000.0010.
 


!!!RECOMMEND!!!

1.|2016 Dec. New 300-115 Exam Dumps (PDF & VCE) 230q download:
http://www.braindump2go.com/300-115.html
2.|2016 Dec. New 300-115 Exam Questions & Answers:
https://youtu.be/dM4mTmskpfk

         

Categories 300-115 Dumps/300-115 Exam Questions/300-115 PDF/300-115 VCE/Cisco Exam

Post Author: mavis

Categories

Archives

Cisco Exam Dumps Download

200-301 PDF and VCE Dumps

200-901 PDF and VCE Dumps

350-901 PDF and VCE Dumps

300-910 PDF and VCE Dumps

300-915 PDF and VCE Dumps

300-920 PDF and VCE Dumps

350-401 PDF and VCE Dumps

300-410 PDF and VCE Dumps

300-415 PDF and VCE Dumps

300-420 PDF and VCE Dumps

300-425 PDF and VCE Dumps

300-430 PDF and VCE Dumps

300-435 PDF and VCE Dumps

350-401 PDF and VCE Dumps

350-401 PDF and VCE Dumps

350-801 PDF and VCE Dumps

300-810 PDF and VCE Dumps

300-815 PDF and VCE Dumps

300-820 PDF and VCE Dumps

300-835 PDF and VCE Dumps

350-801 PDF and VCE Dumps

200-201 PDF and VCE Dumps

350-601 PDF and VCE Dumps

300-610 PDF and VCE Dumps

300-615 PDF and VCE Dumps

300-620 PDF and VCE Dumps

300-625 PDF and VCE Dumps

300-635 PDF and VCE Dumps

600-660 PDF and VCE Dumps

350-601 PDF and VCE Dumps

352-001 PDF and VCE Dumps

350-701 PDF and VCE Dumps

300-710 PDF and VCE Dumps

300-715 PDF and VCE Dumps

300-720 PDF and VCE Dumps

300-725 PDF and VCE Dumps

300-730 PDF and VCE Dumps

300-735 PDF and VCE Dumps

350-701 PDF and VCE Dumps

350-501 PDF and VCE Dumps

300-510 PDF and VCE Dumps

300-515 PDF and VCE Dumps

300-535 PDF and VCE Dumps

350-501 PDF and VCE Dumps

010-151 PDF and VCE Dumps

100-490 PDF and VCE Dumps

810-440 PDF and VCE Dumps

820-445 PDF and VCE Dumps

840-450 PDF and VCE Dumps

820-605 PDF and VCE Dumps

700-805 PDF and VCE Dumps

700-070 PDF and VCE Dumps

600-455 PDF and VCE Dumps

600-460 PDF and VCE Dumps

500-173 PDF and VCE Dumps

500-174 PDF and VCE Dumps

200-401 PDF and VCE Dumps

644-906 PDF and VCE Dumps

600-211 PDF and VCE Dumps

600-212 PDF and VCE Dumps

600-210 PDF and VCE Dumps

600-212 PDF and VCE Dumps

700-680 PDF and VCE Dumps

500-275 PDF and VCE Dumps

500-285 PDF and VCE Dumps

600-455 PDF and VCE Dumps

600-460 PDF and VCE Dumps

Microsoft Exams Will Be Retired

AZ-103(retiring August 31, 2020)

AZ-203(retiring August 31, 2020)

AZ-300(retiring August 31, 2020)

AZ-301(retiring August 31, 2020)

77-419(retiring June 30, 2020)

70-333(retiring January 31, 2021)

70-334(retiring January 31, 2021)

70-339(retiring January 31, 2021)

70-345(retiring January 31, 2021)

70-357(retiring January 31, 2021)

70-410(retiring January 31, 2021)

70-411(retiring January 31, 2021)

70-412(retiring January 31, 2021)

70-413(retiring January 31, 2021)

70-414(retiring January 31, 2021)

70-417(retiring January 31, 2021)

70-461(retiring January 31, 2021)

70-462(retiring January 31, 2021)

70-463(retiring January 31, 2021)

70-464(retiring January 31, 2021)

70-465(retiring January 31, 2021)

70-466(retiring January 31, 2021)

70-467(retiring January 31, 2021)

70-480(retiring January 31, 2021)

70-483(retiring January 31, 2021)

70-486(retiring January 31, 2021)

70-487(retiring January 31, 2021)

70-537(retiring January 31, 2021)

70-705(retiring January 31, 2021)

70-740(retiring January 31, 2021)

70-741(retiring January 31, 2021)

70-742(retiring January 31, 2021)

70-743(retiring January 31, 2021)

70-744(retiring January 31, 2021)

70-745(retiring January 31, 2021)

70-761(retiring January 31, 2021)

70-762(retiring January 31, 2021)

70-764(retiring January 31, 2021)

70-765(retiring January 31, 2021)

70-767(retiring January 31, 2021)

70-768(retiring January 31, 2021)

70-777(retiring January 31, 2021)

70-778(retiring January 31, 2021)

70-779(retiring January 31, 2021)

MB2-716(retiring January 31, 2021)

MB6-894(retiring January 31, 2021)

MB6-897(retiring January 31, 2021)

MB6-898(retiring January 31, 2021)